Descriptions for the Prism Helmet and Motorcycle Mounts

The Prism comes packaged with a wide variety of mounts to fit the needs of installing the Prism onto a helmet or a motorcycle. Here is a description of each of the mounts to use with a helmet or a motorcycle along with an example of how each of the mounts for the Prism can be used.

 

Helmet Mounts

 

Helmet Clamp Kit

Prism_Helmet_Clamp_Mount.jpg

 

The Helmet Clamp Kit enables you to mount the Prism on the side of a helmet. The Helmet Clamp Kit uses a Screw Lock which you can loosen to insert the Support Plate which is what holds the Prism onto the Helmet Clamp Kit. Provided in the package is a rubber pad for placing in-between the Helmet Clamp Kit so that the clamp kit presses against the side of the helmet as much as possible. This is necessary for helmets that are designed with a non-flat surface around the rim of the helmet.

*The Waterproof case cannot be used with the Helmet Clamp Kit.

 An example of using the Helmet Clamp Kit on a helmet.

DSC02158.JPG

 

Glued Surface Mounting Adapter

The Glued Surface Mounting Adapter enables you to mount the Prism on the side of a helmet using the Support Plate without using the Helmet Clamp Kit. This is an alternative to the Helmet Clamp Kit.

*The Waterproof case cannot be used with the Glued Surface Adhesive Mount.

 

An example of using the Glued Surface Mounting Adapter on a motorcycle helmet.

DSC02160.JPG

 

 Helmet Surface Mount

The Helmet Surface Mount enables you to mount the camera on any surface of the helmet. You can adjust the camera angle by rotating the joints. When you are not using the camera, unscrew the camera from the pivot. The Helmet Surface Mount requires the Curved Glued Surface Mounting Adapter.

 

An example of using the Helmet Surface Mount on a motorcycle helmet:

DSC02162.JPG

 

 Goggle Mount

Goggle_Mount.jpg

The Google Mount enables you to mount the camera on the goggle band. This is useful when you wear a helmet and a goggle separately.

*The Waterproof case cannot be used with the Google Mount if you use the Screw Lock and the Support Plate.

 

DSC02164.JPG

 Motorcycle Mounts

 *Note: When using any of the motorcycle mounts, use the QRM wire to tie the Prism and mount to the motorcycle to prevent losing the camera and the mount while riding on the road.

 

Top Surface Adhesive Mount

Top_Surface_Mount1-500x362.jpg

The QRM Top Surface Mount enables you to mount your camera on a flat or curved surface such as windshield, gas tank or a helmet. You can adjust the camera angle by rotating the ball joint on the QRM body. When you are not using the camera, you can simply separate the camera-attached QRM head from the QRM body. The Top Surface Adhesive Mount requires either the Curved Glued Surface Mounting Adapter or the Flat Surface Glued Surface Mounting Adapter.

 

An example of using the Top Surface Adhesive Mount on a motorcycle:

DSC02128.JPG

 

 

Handlebar Mount

Handlebar_Mount.jpg

The QRM Handlebar Mount enables you to mount the camera on your motorcycle’s handlebar (between 7/8’’ and 1 1/2’’ diameter). You can choose the directions of the mounting arm and the U-bolt to best fit the mount on your handlebar. When you are not using the camera, you can take out the camera-attached QRM head from the QRM body.

 

An example of using the Handlebar Mount on a motorcycle:

Prism_Mounts-3.jpg

 

 Dual Suction Cup Mount

Suction_Cup_Mount.jpg

The QRM Dual Suction Cup Mount enables you to mount the camera on surfaces that require some height for recording such as windshield, gas tank, and trunk. You can adjust the camera angle by rotating the wheel joints or the ball joints on the legs. When you are not using the camera, you can simply take out the camera-attached QRM head from the QRM body. The Suction Cup Covers are included in the package for protecting the adhesive of the suction cups when you do not have Dual Suction Cup Mount attached to a surface. 

 

An example of using the Dual Suction Cup Mount on a motorcycle:

Prism_Mounts-56.jpg

 

 Single Suction Cup Mount

QRM Single Suction Cup Mount can be installed on any relatively flat surface on a motorcycle. You can simply adjust the angle to make the view that you want. You can use the short leg that comes packaged with the Prism and one of the two suction cups to make the Single Suction Cup Mount.

 

An example of using the Single Suction Cup Mount on a motorcycle:

Prism_Mounts-21.jpg

Have more questions? Submit a request

0 Comments

Article is closed for comments.